Results 1 to 3 of 3

Thread: PwnageTool 4.0.1 Release information after iOS4 release

  1. #1
    Join Date
    Feb 2008
    Location
    18º24'N ~ 66º05'W
    Posts
    11,479
    Thanks
    503
    Thanked 1,251 Times in 854 Posts
    Downloads
    163
    Uploads
    738

    Default PwnageTool 4.0.1 Release information after iOS4 release

    This is a repost of the latest Dev Team jailbreak/unlock information since iOS4:

    PwnageTool 4.01 Release Info [Download]

    On Monday, Apple released firmware 4.0 for the iPhone and iPod touch devices. This of course was a major upgrade.

    As advised, you shouldn’t have upgraded your devices if you have previously relied on our tools for hacktivation and/or a carrier unlock.

    With that said, today we are releasing PwnageTool 4.01

    PLEASE READ THIS ENTIRE POST CAREFULLY, THERE ARE KNOWN UPGRADE TRAPS AND DIFFERENT UPGRADE SCENARIOS THAT NEED TO BE FULLY UNDERSTOOD AND CONSIDERED BEFORE USING THESE TOOLS.

    Each supported device has few different scenarios that users need to consider when performing the upgrades, you need to check below and perform the upgrade in the particular way that matches your current device state.

    NB: With PwnageTool 4.01 certain devices are not supported this is because they are not supported in iOS 4.0 or they are not supported by our software. We’re working on ways to get past these restrictions.
    • iPhone 2G - not supported
    • iPod Touch - not supported
    • iPod Touch 3G - not supported
    PwnageTool 4.01 only recognizes the official IPSWs that came out yesterday. If you had developer access to the “4.0 GM” IPSWs, do not try to use those.

    iPhone 3GS

    Summary: Currently, PwnageTool only works on previously jailbroken 3GS devices with the old bootrom.
    • If you have a Jailbroken iPhone 3GS with the OLD BOOTROM and you DID NOT use Spirit to jailbreak then you can create the ipsw with PwnageTool 4.0 and restore with your jailbroken recovery mode.
    • If you have an iPhone 3GS with the NEW BOOTROM this is NOT supported by PwnageTool 4.01
    iPhone 3G
    • If you have a Jailbroken iPhone 3G at 3.1.2 (but not jailbroken with Spirit) then you should create the ipsw with PwnageTool 4.01 and restore from recovery mode or DFU mode.
    • If you have an out of the box iPhone 3G you should restore using a PwnageTool 4.01 ipsw using DFU mode.
    • If you have a Jailbroken 3.1.3 iPhone 3G it is very possible that this can fail from recovery mode, if this failure happens you will need to restore using DFU mode.
    • As an alternative to PwnageTool, you can use redsn0w on iPhone 3G (on both Windows and Mac) as mentioned in our last post.
    IMPORTANT! Whenever you need to enter DFU mode, you will need to do so using PwnageTool.

    iPod touch 2G
    • If you have an iPod touch 2G (non-MC model) that is jailbroken (but not with Spirit) then you can restore using recovery mode.
    • As an alternative to PwnageTool, you can use redsn0w on non-MC iPod Touch 2G (on both Windows and Mac) as mentioned in our last post.
    Baseband Unlock
    • As you probably know by now, ultrasn0w has been updated to cover all basebands from 04.26.08 onward. Many thanks to sherif_hashim for finding the crashing command that the new ultrasn0w 0.93 uses! He worked hard at finding the crash, and he kept it confidential until the right time to use it.
    • Major props to oranav (who found the earlier +xlog crash). He also had this crashing command!
    • iPhone 3G and 3GS baseband unlockers (those who rely on ultrasn0w to make phone calls) should always be very wary to update their firmware, however our Ultrasn0w application will unlock all recent (including the current) 3GS and 3G baseband firmware versions. Once you are jailbroken using PwnageTool 4.01, install ultrasn0w from Cydia and you’ll be unlocked.
    • Remember! This baseband unlock situation is rare, should you upgrade your iPhone blindly at the next iOS release please don’t expect an unlock - but for now you are OK (whatever state your baseband is in).

  2. The Following 2 Users Say Thank You to maXimus For This Useful Post:

    Judo (09-21-2010),nsandymary (07-02-2010)

  3. #2
    Join Date
    Mar 2010
    Posts
    128
    Thanks
    3
    Thanked 14 Times in 11 Posts
    Downloads
    12
    Uploads
    0

    Default

    Thank you maximus .
    but this is just for MAC user's ..
    but the windows user's may use Instead of Pwnagetool the Sn0wbreeze ( the new ver )
    We have new guide by Mr . Freakyreflex .

  4. #3
    Join Date
    Mar 2008
    Location
    Asia,Phils
    Posts
    1,291
    Thanks
    473
    Thanked 143 Times in 115 Posts
    Downloads
    8
    Uploads
    1

    Default

    i really prefer for win.......

    ahahahahhaha

    no Mac available here,... i cant afford......

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •